When you’re looking through binoculars and see two of everything, it can be really frustrating. You may think that your worthy binoculars are broken and need to be replaced. But before you go out and spend the money, there are a few things you can do to try to fix them yourself. In this article, we will walk you through 8 steps on how to fix binoculars with double vision.
It is not a simple task to fix collimation in binoculars. Because the lens of binoculars can get easily destroyed if mishandled. So, you must consult a comprehensive guide and understand the nitty-gritty of the problem before you start adjusting your hunting binoculars on your own.
- Why Do Binoculars Have Double Vision?
- How To Fix Collimation In Binoculars?
- How to Fix Binoculars with Double Vision? 8 Easy Steps
- How To Fix Foggy Binoculars
Why Do Binoculars Have Double Vision?
The double vision problem indicates that binoculars are out of collimation. Now you might be wondering, what is collimation? The process whereby all components in binocular lenses are aligned to bright light to their best focus is called collimation. When the process of aligning all components in binocular lenses is not accurate, the binoculars show different images on each side.
In simple words, collimation indicates the entry and exit of light through the lens of the binoculars. In a specific situation, the path light takes gets distorted, and because of the distorted path of light, the user sees two different images from both sides.
How To Fix Collimation In Binoculars?
In most cases, collimation is lost because the user tried to disassemble and re-assemble the binoculars without any expert advice to guide them. While it is important to deeply clean binoculars or adjust their step, the binoculars have delicate parts, i.e., lens and prisms that can easily get misaligned.
Once the lens has been misaligned, it is hard to align them at their original place. Another major reason behind the loss of collimation is mishandling due to the fall of binoculars. The prisms get shifted from their original position when dropped, and collimation is lost.
How to Fix Binoculars with Double Vision? 8 Easy Steps
If you have bought binoculars from a manufacturer that offers a warranty for collimation adjustments, fixing collimation yourself will void that warranty. Refer to the documentation you were provided with when you purchased binoculars to check further warranty details before you proceed to fix them on your own.
As mentioned earlier, binocular double vision is caused when the path of the light entering and exiting the binoculars gets disturbed. By following the steps identified below, you will be able to fix the double vision problem in your rangefinder binoculars, and the quality of the image will improve to a great extent.
The process is likely to take between an hour to two hours, so make sure you have ample time before you begin.
Step 1: Necessary Equipment For Fixing Double Vision
It will save you a lot of hassle and time if you keep the following equipment handy before you start:
You need a screwdriver to help you open tiny screws and a tripod and adaptor to help you position binoculars as you work on them.
Step 2: Find a Target
Position the binoculars on the tripod steadily, just as you would position them to view elements in the sky. Binoculars need to remain steady as you adjust them for collimation. Attaching binoculars to a binocular tripod will make sure they stay steady.
Now focus the lens on an object to see a clear picture. The picture can be of a fence, a tree, or any other still object at least 1 kilometer away. Focus the binoculars on the selected object and keep binoculars steady in that position.
Step 3: Test the Collimation
A double picture indicates that the collimation is not right. You may also perform another test to ensure collimation. Close your eyes for a few seconds and then refocus on the thing when you open them. Collimation is not a problem if it looks to be a single picture. If you still see a duplicate picture, make the necessary modifications.
Step 4: Removing Plastic Casing
If your binoculars have a plastic casing, you will need to remove them using a scalpel or razor. Start removing the casing above the eyepiece and move towards the outer corners of the binoculars. Ensure to keep the blade away from the binocular lens so that they do not get damaged.
Before proceeding, you also need to remove the plastic coating on the adjustment screws. Also, remove the lens, clean it and place the clean lens back.
Step 5: Find Adjustment Screws – Fix Binoculars with Double Vision
Using diagrams in the user manual of your binoculars, you will be able to locate the adjustment screws on your binoculars. They are typically covered with plastic or glue, making it difficult to find them.
If you cannot find the location of screws using the user manual, you can find relevant details about your binoculars using a google search. The manufacturer may have uploaded the diagram of your binocular model, and you can use it to find the screws.
You will find the horizontal adjustment screws before the eyepiece at the back rim of the binoculars. The vertical screws are placed at the center of the binoculars, and you can find them after you peel off the casing on each side of the knob.
Step 6: Adjust the Screws
After this, you can start adjusting the horizontal and vertical screws. Keep track of the number of turns you complete on each adjustment screw, so you can repeat the process in case you make a mistake.
We recommend you start with horizontal screws. Turn each of the two horizontal screws by one-eighth of a turn, alternating between each screw as you do this. Carefully adjust each screwat at the same time and an equal angle. Otherwise, you will not notice any improvement.
Make sure you follow a similar procedure for each side of the binoculars. Once you finish rotating the horizontal screws, you need to adjust the vertical screws similarly.
Alternatively, turn each screw by one-eighth of a turn, taking breaks as you do this. Again, be careful to adjust each screw simultaneously and at an equal angle. Make sure you follow a similar procedure for each side of the binoculars.
Step 7: Tightening the Screws
Once you have adjusted horizontal and vertical screws, proceed with the following instructions. The following paragraphs will guide you on how to tighten the screws.
Begin with the horizontal screws of each side because it is harder to align horizontal screws in comparison to vertical screws. Tighten the horizontal screws until the images are halfway closer. Make sure to turn them slowly and adjust each side halfway and equally to preserve the picture quality.
Once one horizontal screw of each side has been adjusted, move to the other horizontal screw to bring the images closer. Turn it slowly until images continue getting closer and stop when images stop getting closer.
When you observe the images start getting further, you should know that your horizontal adjustment is complete. The images will not be centered yet as you still need to fix vertical screws. When you have tightened horizontal screws, switch to vertical screws.
Turn one of the vertical screws and see if it brings the images closer. As you observe the images getting closer, continue turning them until they are halfway closer. Then adjust the other vertical screw until you see the images get centered. Follow a similar procedure for each side of the binoculars.
Step 8: Refocus Lens and See Results
When you are satisfied that images are on top of each other, turn the right-hand knob to its original position and see if the resulting image has improved. To be sure, perform the test for collimation again. Focus the lens on an object to see a clear picture. If you solved the double vision problem, your adjustment procedure was successful.
If you still observe a double image, collimation is not right.
How To Fix Foggy Binoculars
Have you ever been out in the field, hunting or bird watching, and had your binoculars fog up on you? It’s one of the most frustrating things that can happen, especially when you’ve finally spotted your prey.
Even the binoculars manufactured by the best companies can suffer from foggy lenses. This can be a major problem, as it can impair your vision and make it difficult to spot game. So what can you do to fix foggy binoculars?
You don’t gave to worry, there are a few easy ways to fix foggy binoculars. The best way to prevent your binoculars from fogging up in the first place is to make sure they’re clean and dry before you use them. This means wiping down the lenses with a soft, clean cloth.
You should also store your binoculars in a dry, cool place when you’re not using them. If your binoculars do start to fog up, there are a few quick fixes. One is to simply breathe on the lenses and then wipe them off with your cloth. Another option is to use a lens cleaner specifically designed for binoculars. You can also try placing your binoculars in a bag of rice overnight. This will help to absorb any moisture that may be causing the fogging.
With a little effort, you should be able to fix your foggy binoculars and get back to enjoying your favorite hunting spots.
Conclusion – How to Fix Binoculars with Double Vision
You should know that binoculars require maintenance to be of use continuously. In case a fault such as double vision occurs, do not fret. Instead of immediately replacing it, try fixing it yourself or using an expert’s help.
I recommend you opt for an expert repair if your binoculars are new and under warranty. However, if it’s old and the option of warranty is not available, the process of how to fix binoculars with double vision in this article will help you.
- How To Choose A Recurve Bow 2022 – Ultimate Guide - October 5, 2022
- 7 Best Rangefinder Binoculars for Hunting in 2022 - September 18, 2022
- Moose Size Comparison – How Big is a Moose Compared to Other Animals? Interesting Facts with Pictures - September 18, 2022